Engine Flush
Bud's Tire & Wheel can perform a complete set of advanced preventative maintenance options for your car, truck or SUV with some of the most advanced machines available.
While oil filters remove most of the sludge, tar, and varnish, small particles continue to circulate inside the engine and accumulate within the passageways, oil pump and oil pan. These contaminants cause engine wear, higher operating temperatures, and reduced lubrication.
With the Bilstein R-2000™ Engine Flush System, contaminants are not just re-circulated but actually removed from oil passages and the entire engine oil system. This unique system thoroughly cleans your engine by using patented adaptors and specially formulated solutions to dissolve accumulations of sludge, tar, and varnish. All residual oil and cleaning solutions are evacuated ensuring your engine, ring seating, valve guides and seals are not harmed in the process.
- Heated R-2000 Engine Flush solution is pumped through the oil filter port at 42 PSI.
- R-2000 Engine Flush solution flows through the engine's lubrication system dissolving sludge and varnish.
- R-2000 Engine Flush solution backflushes the oil pump pickup screen. Dissolved sludge, varnish and debris flow to the oil pan where it is vacuum extracted to the BILSTEIN R-2000 Engine Flush Machine. Particulates over 3 microns are removed through three stages of ultra-fine filtration.
Periodic sludge removal restores operational efficiencies, gives you better fuel economy, and will ensure a longer engine life for your vehicle.
Δ Top of Page Δ
Carbon deposits and other contaminants in gasoline will eventually clog the tiny spray nozzles of your fuel injectors. Your car, truck, or SUV should be serviced with our Liquid Fuel Injection System Service every 15,000 to 20,000 miles, or if you notice any of the following:
- Decreased gas mileage
- Engine pinging
- Poor acceleration
- Sputtering or stalling
Your auto's cooling system gets a strenuous workout over the course of an Inland Empire Summer, and flushing your cooling system is vital to keeping your car, truck, or SUV running. Over time the coolant mixture loses its effectiveness and lubrication abilities, and will even become acidic after long-term use, causing catastrophic damage to your cooling system and engine block. To perform at its optimum level, most cooling systems require a 50/50 solution of radiator coolant to water. Bud's Power Flush Service will provide these benefits:
- Removes any rust particles, corrosion, and contamianation from the entire cooling system, not just the radiator
- Replenish the system with the correct 50/50 mixture of coolant/water, which:
- Allows the cooling system to run at peak efficiency
- Protects metal surfaces against rust and corrosion
- Lubricates the water pump
The fluid in your power steering system is subjected to extreme temperatures and pressures. Over time the fluid is subject to deterioration and breakdown, oxidation, and accumalates contaminants, varnish deposits, and bare metals that can cause leaks, difficult steering, and system breakdown. The Ever-Wear power steering system flush provides the following benefits:
- Removal of contaminants, deposits, wear metals, and debris
- Reduction in wear, premature component failure, valve sticking, and squeal
- Restores quiet, smooth, uniform steering control, and lubricity
- Provides safe, secure steering
According to the Automatic Transmission Rebuilders Association, 90% of all transmission failures are due to overheating and fluid contamination. A typical transmission fluid service will only replace 20% of the fluid in the transmission; draining the collected fluid in the pan, but leaving behind the old, contaminated fluid inside the torque converter, transmission cooler and the cooler lines. Our transmission flush safely replaces all of the old fluid trapped throughout the entire system with fresh new fluid. This service is recommended every 30,000 miles and before warranty expiration to detect potential problems.
-
Features & Benefits:
- Dissolve & suspend gum & varnish in the valve body
- Flush old fluid and debris from system
- Install fresh new fluid
- Eliminates hard shifting, chattering and gear slipping
- Reconditions seals and extends transmission life
- Provides cooler operation
